Interline Publishing
 info@interlinepublishing.com +91 98867 328 23 / 24 / 25   +91 80 2333 2824 Sign Up   Sign In
Interline Publishing
Skip to Reader

Procedure video

     
 
AU Steel Structures - I Sem V
Unit 3 : NA((a)Tension members : Types of tension members, Design of strands, slenderness ratio, displacement of tension members, behavior of tension members, modes of failure, factors affecting strength of tension members, angles under tension, design of tension members, Lug angles, splices, (b)Compression members: Possible failure modes, classification of cross-section, behavior of compression members , Effective length, radius of gyration and slenderness of compression members, Allowable stresses in compression, Design of axially loaded compression members, Built up compression members, Laced and Battened columns, eccentrically loaded columns, Column splices)
1. Column and Struts, Thick and Thin Cylinders(Mechanics of Materials ) Total View (16)
 
Introduction to columns and struts, Failure of a column, Expression of crippling load when (a) both ends are hinged (b) One end of the column is fixed and the other end is free (c) both ends are fixed (d) One end is fixed and the other end is hinged. Simple problems to be solved used Euler's formula and Rankine formula Thick and Thin Cylinders Thin cylinders subjected to internal pressure. Stresse ......
Title: Mechanics of Materials through Problems and Solutions
Published on: 01/06/15
Author: Balachandra P Shetty (Wg Cdr Dr. PB Shetty) and Rachith S.N
Publisher: Interlinepublishing
Pages: 33
Price: Rs 24.75

2. Unit - III(Aeronautical Engineering) Total View (19)
 
Strain Energy in axial, bending, and torsion loadings. Castigliano’s theorems-Maxewell’s Reciprocal Theorem-dummy load & unit load methods-application to beams, frames, rings & trusses. Columns Euler’s column curve-Rankine formula-inelastic buckling-effect of initial curvature-the South well plot-columns with eccentricity-use of energy methods-theory of beam columns-beam columns with differe ......
Title: Aircraft Structures-I
Published on: 20/06/16
Author: Balachandra P Shetty (Wg Cdr Dr. PB Shetty) and Rachith S.N
Publisher: Interlinepublishing
Pages: 41
Price: Rs 30.75

3. Hardened Concrete(Materials of Construction) Total View (444)
 
Freshly mixed concrete before set is known as wet or green concrete whereas after setting and hardening it is known as 'set or hardened concrete'. This chapter deals with the properties of hardened concrete.
Title: Materials of Construction
Published on: 28/10/14
Author: Manjunath KS
Publisher: Sanguine Technical Publishers
Pages: 42
Price: Rs 31.5

4. Solved Question Paper 2(Mathematics) Total View (19)
 
Solved Question Paper
Title: Strength of Materials
Published on: 30/11/16
Author: Leeladharesh
Publisher: Saividya Institute of technology
Pages: 20
Price: Rs 10

5. Chapter 13 * Load and Type of Structures(Civil Enginnering) Total View (0)
 
Before designing any structure it is necessary to have knowledge about various types of loads which are imposed on any structure. Depending on worst combination of load, structure is designed by considering suitable amount of factor of safety which differs from structure to structure, its purpose and basically worst load calculated.
Title: Strength of Materials - 4th Edition
Published on: 11/02/19
Author:
Publisher:
Pages: 10
Price: Rs 5

6. Helicopter Airframe & Transmission System Design Concepts(Aeronautical Engineering) Total View (4)
 
Airframe, Transmission System Design, Gears, Clutches, Transmission shafting, lubrication, rotor brakes, rotor system design concepts, Life load relationship, Good design practices for Gearboxes, Gearbox lubrication considerations, bearings, Main rotor transmission design concepts, Rotor design concepts, Materials for rotor hubs, Upper control system design, anti-torque rotor transmission, Modern ......
Title: Helicopter Technology
Published on: 07/06/17
Author: Simon K John & Balachandra P Shetty
Publisher: Interlinepublishing
Pages: 69
Price: Rs 37.95

7. Fundamentals of Aircraft Design (Aircraft Production)(Aeronautical Engineering) Total View (7794)
 
Principles of flight • Aerodynamics characteristics • Aircraft manoeuvres • Aircraft performance • Basic functions of the aircraft structure • Loads imposed on aircraft structure • Loads imposed on aircraft structures • Structural design considerations • Aircraft configuration and principal types of construction • Details of constructional features of ......
Title: Aircraft Production Technology and Mangement
Published on: 28/10/14
Author: Keshu S C and Ganapathi K K
Publisher: Interlinepublishing
Pages: 83
Price: Rs 62.25

8. Unit - I(Aeronautical Engineering) Total View (71)
 
Loads on Aircraft Structural nomenclature-Types of loads-Load factor-Aerodynamic loads-Symmetric maneuver loads-V-n diagram-Function of structural components. Materials for Aircraft Structures Metallic and non-metallic materials, Use of Aluminium alloy, Titanium, Stainless steel and Composite materials, Desirable properties for aircraft application Mechanical Properties of Material Stress-s ......
Title: Aircraft Structures-I
Published on: 28/08/15
Author: Balachandra P Shetty (Wg Cdr Dr. PB Shetty) and Rachith S.N
Publisher: Interlinepublishing
Pages: 37
Price: Rs 0

9. Chapter 15 * Analysis of Columns(Civil Enginnering) Total View (0)
 
Column is a compression member, which is subjected to axial force or eccentric force, which causes either direct stress or direct and bending stress. If load on column is excess then the column is likely to buckle and this nature of buckling differs from its end conditions. A column can be either short, medium or long depending on mode of its failure. A column which fails due to crushing is called ......
Title: Strength of Materials - 4th Edition
Published on: 11/02/19
Author:
Publisher:
Pages: 16
Price: Rs 8

10. Mechanical Behaviour of Metals and alloys(Mechanical Engineering) Total View (3)
 
Stress-Strain Diagrams, Creep behavior, Fatigue and Fracture.
Title: Material Science and Metallurgy
Published on: 01/02/18
Author: Dr Dasharath S M
Publisher: Interlinepublishing
Pages: 26
Price: Rs 19.5

11. Introduction to Composites(Composite Material) Total View (151)
 
Mankind is aware of composite materials from time immemorial. To mention a few: Houses made of mud bricks from clay reinforced with straw (1500 BC), Mud walls of houses reinforced with bamboo shoots (500BC), Glued laminated wood (500BC), Laminated metals in forging swords (1800 AD), Glass fibers reinforced resins for boats and aircrafts (1930). Since then, many modern composites have been develop ......
Title: Composite Materials
Published on: 13/11/14
Author: A Team of Experts
Publisher: Subhas Stores
Pages: 49
Price: Rs 0

12. Fiber Reinforced Plastic Processing(Composite Material) Total View (111)
 
Unique to the composites industry is the ability to create a product from many different manufacturing processes. There are a wide variety of processes available to the composites manufacturer to produce cost efficient products. Each of the fabrication processes has characteristics that define the type of products to be produced.
Title: Composite Materials
Published on: 13/11/14
Author: A Team of Experts
Publisher: Subhas Stores
Pages: 46
Price: Rs 34.5

13. Contents(Civil Enginnering) Total View (2)
 
Strength of Material is an important subject in the curriculum of Civil Engineering and Architecture Students of Diploma and degree course. The book is focused mainly for the students of various universities all over INDIA. the language of the book is simple and text is elaborated with suitable examples and sketches where ever required.
Title: Strength of Materials - 4th Edition
Published on: 11/02/19
Author:
Publisher:
Pages: 12
Price: Rs 0

14. Introducion to Metal Forming Processes, Forging, Rolling, Drawing, Extrusion, Sheet Metal and High Energy Rate Forming(Manufacturing Technology-III) Total View (1)
 
Introducion to Metal Forming Processes, Forging, Rolling, Drawing, Extrusion, Sheet Metal and High Energy Rate Forming
Title: MANUFACTURING TECHNOLOGY-III
Published on: 31/01/18
Author: Shanawaz Patil
Publisher: Interlinepublishing
Pages: 63
Price: Rs 47.25

15. UNIT - 8 Behavior of Tribological Components: (Mechanical Engineering) Total View (5)
 
Selection, friction, Wear of ceramic materials, wear measurements, effects of speed, temperature and pressure. Tribological measures, Material selection, improved design, surface engineering.
Title: Tribology/10ME831
Published on: 20/02/17
Author: MOHAMMED NAVEED
Publisher: Ghousia College of Engineering
Pages: 18
Price: Rs 10.8

16. Introduction to Elasticity(Physics) Total View (1391)
 
• Introduction • The General Theory of Elasticity • Assumptions of Linear Elasticity • Applications of Linear Elasticity
Title: Applied Elasticity
Published on: 28/10/14
Author: Sitharam T G
Publisher: Interlinepublishing
Pages: 4
Price: Rs 0

17. Composite Materials and Honeycomb Structures(Aeronautical Engineering) Total View (7792)
 
• Properties of composite materials • Comparison of properties of composite materials with conventional metallic alloys • Process of manufacturing composite components • Quality control • Ultrasonic techniques of inspection • Boron fibre composites • Aramid fibre composites • Sandwich structures.
Title: Aircraft Production Technology and Mangement
Published on: 28/10/14
Author: Keshu S C and Ganapathi K K
Publisher: Interlinepublishing
Pages: 29
Price: Rs 21.75

18. THEORY OF METAL CUTTING(Manufacturing Process - II ) Total View (6)
 
In an industry, metal components are made into different shapes and dimensions by using various metal working processes. Metal working processes are classified into two major groups. They are: Non-cutting shaping or chips less or metal forming process - forging, rolling, pressing, etc. Cutting shaping or metal cutting or chip forming process - turning, drilling, milling, etc.
Title: Manufacturing Technology-II
Published on: 31/01/18
Author: Gururaja Sharma T
Publisher: Interlinepublishing
Pages: 17
Price: Rs 34

19. Sheet Metal Forming (Aircraft Production)(Aeronautical Engineering) Total View (7812)
 
• Sheet metal operations • Shearing • Punch press operations • Power brake operations • Routing • Rubber press forming • Fluid cell press forming • Drop hammer and drop stamp forming • Stretch wraps forming • Peen forming • Spinning • Diffusion bonding.
Title: Aircraft Production Technology and Mangement
Published on: 28/10/14
Author: Keshu S C and Ganapathi K K
Publisher: Interlinepublishing
Pages: 50
Price: Rs 37.5

20. SPRINGS(Machine Design ) Total View (2)
 
helical springs,spring rate,stiffness of springs,material of springs,manufacture of springs,spring ends,buckling of compression springs,surging of springs,conical springs,belleville springs,design for procedure,derivation of expression for deflection Y,laminated spring,design procedure for laminated springs,equalization of stress in spring leaves
Title: Design of Machine Elements II
Published on: 24/04/17
Author: Annaiah M H
Publisher: Dr Sri Sri Sri Shivakumara Mahaswamy College of Engineering
Pages: 85
Price: Rs 21.25

21. Unit-06(Civil Enginnering) Total View (2)
 
Design of Rigid Pavement: Design of CC pavement by IRC: 58 - 2002 for dual and Tandem axle load - Reinforcement in slabs - Requirements of joints -Types of joints - Expansion joint - contraction joint - warping joint - construction joint - longitudinal joint, Design of joints, Design of Dowel bars, Design of Tie bars - problems of the above
Title: Pavement Design
Published on: 23/03/17
Author: Dr Mohammed Ilyas Anjum
Publisher: Ghousia College of Engineering
Pages: 5
Price: Rs 3

22. UNIT-2 2.1 COMPARATORS AND ANGULAR MEASUREMENT(Mechanical Measurement & Metrology) Total View (2)
 
Comparators can give precision measurements, with consistent accuracy by eliminating human error. They are employed to find out, by how much the dimensions of the given component differ from that of a known datum. If the indicated difference is small, a suitable magnification device is selected to obtain the desired accuracy of measurements. It is an indirect type of instrument and used for li ......
Title: Mechanical Measurements & Metrology
Published on: 30/01/18
Author: PRADIP GUNAKI
Publisher: Interlinepublishing
Pages: 34
Price: Rs 25.5

23. Chapter 12 * Direct and Bending Stresses(Civil Enginnering) Total View (0)
 
When a imposed load passes through C.G of the section then it is axial load which can be either pulled or pushed [Tensile or compressive].
Title: Strength of Materials - 4th Edition
Published on: 11/02/19
Author:
Publisher:
Pages: 30
Price: Rs 15

24. Fabrication of Pipe Lines and Tubular Conduits (Aircraft Production)(Aeronautical Engineering) Total View (7811)
 
• Types of pipelines and tubular conduits • Routing of pipelines • Cleaning of pipelines • Inspection of pipelines
Title: Aircraft Production Technology and Mangement
Published on: 28/10/14
Author: Keshu S C and Ganapathi K K
Publisher: Interlinepublishing
Pages: 8
Price: Rs 6

25. Machining Process (Aircraft Production)(Aeronautical Engineering) Total View (7800)
 
• Mechanics of metal cutting • Cutting tool materials • Tool geometry • Machinability and cost of machining • Turning operations • Drilling • Reaming • Boring • Milling • Broaching • Grinding • Honing and lapping • Electric discharge machining • Electrochemical machining.
Title: Aircraft Production Technology and Mangement
Published on: 28/10/14
Author: Keshu S C and Ganapathi K K
Publisher: Interlinepublishing
Pages: 63
Price: Rs 47.25



 
Home
About Us
Payments
Contact Us
Claims
Help
Advertising Guidelines
Safe and Secure Payment
All major credit and debit cards are accepted.
Policies: Terms of Use | Privacy    Copyright © 2019 Interline Publishing. All rights reserved.